Showing 17–32 of 86 results

  • DDM LOP

    • Supply voltage 12VDC/24VDC as per customer requirement.
    • Three 1 inch ( 5×7 ) DOT MATRIX modules are used in this card. One Dot Matrix is used for showing elevator direction indication with the scrolling Arrow & another two dot matrix are used for  up to two digit floor indicator.
    • All inputs are -ve (GND).

  • DOB ANNOUNCEMENT

    • Operating voltage from 12V TO 24V AC/DC.
    • Compact & designer box with 8 ohm speaker.

  • EP-1998

    LOGIC BOARD FOR V3F ELEVATOR CONTROL PANEL

    Maximum 40 stops with extension card.

    (G+39 down collective / G+23 full collective)

  • EX-200

    • Floor Extension board.
    • On board number of stops 8 .(8 landing calls).
    • Compact in size.
    • Easy connection with the Main logic board using FRC (Flat Ribbon Cable).

  • EX-202

    • Elevator floor Extension board.
    • On board number of stops 16 .
    • Easy connection with Main logic board & other extension card with the FRC(Flat Ribbon Cable).

  • EX-3003

    • Elevator Floor Extension board.
    • On board number of stops 16 .(8 landing calls & 8 car calls).
    • Easy connection with Main logic board & other extension card with the FRC (Flat Ribbon Cable).

  • EX-485

    • Modbus Communication Card.
    • On board Modbus communication RX/TX LED indication.
    • Easy connection with the Main logic board using FRC (Flat Ribbon Cable).
    • No supply voltage requirement for Extension card.

  • EX-5001

    • Elevator Floor Extension card.
    • On board number of stops 16 .( 8 Landing calls, 8 Car calls & 8 Reed Input ).
    • Easy connection with the Main logic board with the FRC (Flat Ribbon Cable).

  • G+15 SER-CT

    • Serial Cartop board.
    • Supply Voltage Requirement 24VDC.
    • On board 16 Stop (G to 15) Car call is present with call registration indication.
    • Having Maximum 24 (G to 23 ) Car calls using extension cards

  • G+4 HYDRO

    Logic board for V3F & DUMBWAITER Elevator Supply voltage requirement 12VDC & 110VAC for safety. On board number of stops 5 (G+4). Door operation – -Manual Door Speed support up to 0.7 m/s. Reed signals FLOOR REED & CABIN TOP REED as per requirement. On board a small 7 SEG display available for floor indication….

  • G+5 RELAY

    • Relay board use with the G+5 single speed logic board.
    • Supply voltage requirement 12VDC & 110VAC for safety.

  • G+7 HYDRO

    Logic board for HYDRAULIC ELEVATOR. Supply voltage requirement 12VAC, 24VDC & 110VAC for safety. On board number of stops 8. -(G+7 down collective / G+5 full collective). Door operation – -Manual Door -Auto Door User configurable with LCD display & keyboard. Input Reed signals CABIN TOP REED. LCD display showing status & errors. Status of…

  • G+7 SER-CT

    • Serial CARTOP board.
    • Supply Voltage Requirement 12VDC/24VDC.
    • On board 8 Stop ( G to 7 ) car call is present with call registration indication.

  • HYDRAULIC DOOR RELAY

    • Door Relay card for hydraulic lift  vertical Door.
    • Microcontroller base relay card so we can assign multiple door output at time, because of which both side door opening possible as per
      user early requirement.

  • HYDRAULIC RLB

    • Supply voltage for the relay card is 12VDC/24VDC as per requirement.
    • This card has 5 REED inputs & 5 Relay outputs.

  • ICON 3PH 110VDC PS

    This rectifier is use only when we have 3-phase transformer having 3-phase 110VAC output. Having two bridge rectifier 1) 3-phase 110VDC for break & R-CAM. 2) 24VDC for slowing safety & logic board. Extra one fuse with input & output connector. LED Indication at rectifier output.